
HA HUNG TRADING AND SERVICES CO.,LTD
Địa chỉ: 406/55 Cong Hoa, Phường 13, Quận Tân Bình, Thành Phố Hồ Chí Minh
Điện thoại: 028.38464877 EXT 101 | Fax: (8428) 38464877
Hotline: 0906.613.677 (Ms Sương) - 0932 679 576 ( Ms Thư)
Email: [email protected] - Website: www.hahung.vn
Installation manual UPS
UPS after buying about, we will carry out the installation. UPS, also known as UPS want to use an effective and lasting time, customers should read through the instructions and notes in a general way.
UPS installation has many different sequence. First, the need to dismantle the shell UPS box to check. Note: This UPS series weight of relatively heavy, be careful in the process of transporting goods. Remove the outer shell UPS box. Remove gently, and sequentially arranging the device in the packaging. UPS box will include: APC UPS and accompanying accessories like manuals books, papers relating to products, communication cables, wires ... For the time UPS UPS long time, it will have more external battery cord. If any one is broken caused by the transportation or missing any parts, so please keep the scene intact, do not turn on the UPS and notify the distributor or the customer service center APC
Notes on installation of UPS have the following:
- Power distribution equipment must be placed in a cool place, well ventilated, avoid damp areas, near water, where explosive or corrosive substances.
- Do not place the UPS tilt. Uncovered part of any UPS section to ensure aeration process. Plus temperature around UPS should ideally remain between 0-40 ° C.
- Loss pin power supply current to be located near UPS APC, easy draw in emergencies to disconnect power and unplug.
Note: You must disconnect power to the load device when connecting devices to the UPS load, and then turn on each device to load. Ensure each process.
- Online UPS battery should recharge within 08 hours before use (avoid power consumption over time by climate, external actors ...). We just need to use cords of UPS input socket with 01 mains power socket nearby. Restart UPS, UPS will automatically recharge the battery and can be used immediately without charging extra electricity.
Method of UPS connections:
First, the user must consult before the technical documentation of each UPS corresponds to the exact connection and safe to install.
APC provides kits full specifications of all model lines to UPS customers can consult as needed. The most important is compliance with regulations on size standards cords, fuses, automat ... to provide power to the UPS.
- When connected to utility power, the UPS placed to work in bypass mode or not is thanks WinPower software. For models from 6000VA or more, run bypass mode preinstalled,
- Press and hold the "Power on" for more than 1 second to turn on the UPS. If you do not see on the phone, hold the button for 3 seconds.
- After activation, APC UPS equipment will begin the process of self-examination with the indicator light (lamp 1-6).
Off APC UPS is connected to the mains:
1. Press and hold the "Power off" continuously for 3 seconds or more to turn off the UPS and have time for converters also be turned off by.
2. During the time off, APC UPS self-test will begin. The bright lights are respectively 1-6 bottom-up faded. If software WinPower placed in bypass UPS and lights will be turned on to indicate that the APC UPS is working under bypass mode.
3. After you have completed the steps above to turn off APC UPS, UPS output socket of the APC still current. To interrupt the output power of the APC UPS, simply disconnect the power supply and UPS will begin self-examination. All LEDs are off, no power source socket. APC UPS is turned off.
In the absence of power supply, UPS is operating off battery mode (same as above GPs)
In the power user mode, also known as wire mode. Power indicator and warning lights lit adapter. LED signal transmission device is turned on capacitance matching of power transmission equipment is connected.
1. If the power indicator light flashes regularly, it said there are problems with extreme mixed game (L, N), but this can lead to short-circuiting. UPS is still in working condition in the power mode. If the battery indicator lights up at the same time, this indicates the voltage or mains frequency beyond the normal range for the input of the UPS. UPS switched to operate in battery mode.
2. Guests should note if output overload, the overload indicator lights will be turned on the light and alarm will sound 2 beeps immediately for 1 second. Then the user has to interrupt a transmission device not needed to reduce the number of devices connected to the UPS load is less than 100% so that the capacitance of APC UPS.
3. If the indicator light flashes ac-regulation, signaling that the battery is not connected to the UPS or the supply voltage for the battery too low. Workarounds should check that ac-regulation can be connected with UPS adequate? If you check the connection between the UPS and batteries no matter what it may be due ac-regulation problem or the shelf.
Upon the occurrence of the problem of electricity, supplied with power from the generator to the UPS, you should follow these steps:
Run the first generator, wait until the generator stable operation and then only output socket connects the generator to the UPS (be sure ups APC UPSs are not working mode ). Next, turn on UPS APC boot process as directed above. After the UPS is turned on, a new connection each device in turn power the UPS load. Can and should choose AC generator with a capacity of 1.5 times the UPS.
The installation and note the operating procedures APC UPSs very important, it will affect the work between devices on a consistent basis, not occur risks, while reducing the impact intrusion APC UPS to operate. The most important is the safety of people.
DISTRIBUTION CENTER AND REPAIR UPS HOP THANH THINH
Ad : 145/10 Pham Van Hai Street, Ward 5 , Tan Binh District , Ho Chi Minh City
Tel : 0932.153.163 / 0908.316.209 (Mr Han )
Yahoo / Sky : trannguyenhanvn
Website : http://www.boluudien.biz